Centre Technology Transfer CITTRU posted this:Carbon composites based on bacterial biomass for manufacturing of electrode materialsThe subject of the offer is a method of manufacturing of carbon-based composites for electrode materials. These composites are built of electrode active phase nanoparticles (e.g. metallic or metal oxides) and a carbon matrix obtained from bacterial biomass. Living organisms serve both as the component capable to capture the nanoparticles, and as a source of biocarbon support providing high dispersion and stabilization of nanoparticles, as well as high electrical conductivity of the material. Application: electrocatalytic active electrode materials, e.g. in ORR reactions; energy storage (supercapacitors).
Mª Eugenia Garcés Castellote posted this:
Commercialization Specialist at Universidad de Alcalá-OTRI
Alexander Kvashnin posted this:
Director at Center for Technology Transfer and Commercialization of Novosibirsk State University
Claude Waudoit posted this:
Carlos Barrera posted this:
Graft Polymer UK Ltd posted this:Project: Innovative pilot production modified compounds by PE125 standard for multifunctional applications.Producing PE125 using GRAFTALEN™ MP-UHHD. Consumer properties, which should be taken into consideration: 1) The unique toughness of the material (the highest rate of all known polymers), namely, Over 160 kJ/m2 2) High abrasion resistance 3) Low friction coefficient (self-lubricating) 4) High resistance to chemically aggressive reagents (media) 5) High creep resistance (geometric stability) Ordinary way - This type of process is quite expensive. Production of PE125, in compounding with bimodal PE100, from 8 to 45% of supermolecular polyethylene is injected, reaching dispersion by multiple compounding (4 stages) in an extruder cascade (XXXXX technology). GRAFTALEN™ MP-UHHD (alloy) is a MELT-PROCESSABLE concentrate of UHMWPE on an HDPE matrix. As HDPE, you can choose the most affordable HDPE (pipe) grade. To obtain polyethylene according to the standards PE125 (with a minimum strength indicator MRS> 13.8-14 MPa, in comparison PE100 has MRS only 10 MPa), a significant improvement in the resistance against hydrostatic pressure is required. For a conventional bimodal HDPE, this indicator is difficult to achieve, since it directly correlates with the impact strength/density indicators and with simple extrapolation, it turns out that the required indicator for PE125 simply does not reach the bimodal HDPE matrix. Another problem - the difficulty in maintaining the geometric stability of the pipe (the thickness at the top of the pipe is often less than at the bottom) due to the sagging effect (the phenomenon of the gravitational flow of a polymer melt). This phenomenon is more pronounced for thick-walled pipes. The specific blend of HDPE with UHMWPE allows solving these problems above.
Ilythia Morley posted this:
Intern - Commercialization Team at Korea Institute of Energy Research
INESC TEC posted this:a single-stage, bidirectional and high-frequency isolated power conversion systemACDC Cube is a single-stage, bidirectional and high-frequency isolated power conversion system. ACDC Cube also uses a novel control method to do the interface between the Alternate Current (AC) distribution networks and a battery pack, or other Direct Current (DC) sources/loads, delivering higher power quality in a compact design. ACDC Cube has lower total volume and weight, increased durability and equivalent reliability when compared with a standard solution such as the voltage source converter plus dual active bridge. Due to its innovative features, ACDC Cube is especially suitable for applications where the size of the power conversion system is critical.
Peter Mogyorosi posted this:
CEO at Laser Consult Ltd.
NDI Foundation posted this:NEW FLUORINATED CARBON MATERIALS FOR FUEL CELLS AND BATTERIESOur project is the solution for sorting out rechargeable batteries enchanted anode and fuel cells Proton Exchange Membranes (PEM) efficiency issues. We propose to start mass production and sales of the products based on the new technology of Soft Fluorination for Carbon Materials and products derived by this technology. Our product is globally prospective and ready for industrial use. The product is targeted to the following segments of clients: - fuel cells producers - proton exchange membranes (PEM); - energy storage systems - batteries and super-capacitors electrodes; - Super-acid Catalysts for numerous uses; - Fillers for fluorinated resins; - Biologically indifferent sorbents (e.g. for blood purification); - Hydro-isolation of resins adhesion of construction composite materials and pigments. As so far in the fuel still not realized their potential as a cost efficient, environmentally friendly and productive in converting available chemical energy into electric energy.
University of Huelva posted this:Power supply system controlled from internet for devices connected to a lanNowadays there are devices that allow the control of devices connected to a network from the own network. The classical method to access them from a different network is the redirection of the corresponding TCP or UDP connections to local networks from the border router. The redirection requires a high level of expertise in communications to be performed. Another strategy that is often used is the creation of VPN (virtual private network). This technique allows the control of access but does not allow connections to be discriminated or the management of power supply. The proposed system allows you to control the person and the moment to access as well as the free access. The modification of these constrains can be performed in the course of an access session. In addition, the system allows the control of power supply of the device you want access to. The interface is very friendly and does not require continuous changes in the configuration of the router. The system has a local database access control and validation can be delegated to other servers using protocol validation like LDAP, IMAP, POP3, etc.
Universidad de Alcalá-OTRI posted this:GEISER Research Group and its Power Electronic LabThe Group of Electronic Engineering Applied to Renewable Energy Systems of Alcalá University (GEISER) presents the Power Electronics Research Lab, as a place to Research and Development, equipped with all of the tools and instrumentation necessary for the development of power electronic systems. That includes: - Yokogawa oscilloscopes - Power analyzer and data loggers - a dSPACE system - a Regatron Full 4-quadrant grid simulator and - ADS AC/DC electronic loads ....among others.
University of Huelva posted this:Synchronized exchange energy method and device between users of the electric grid for decentralized managementThe method comprises defining fragments of energy to be demanded at given time intervals by consumers of the electrical network, negotiating their purchase with providers or other users capable of bidding, synchronizing production and consumption, and storaging or providing the difference between the negotiated fragment and the amount of energy actually demanded or suplyed with zero-impact on the grid
University of Huelva posted this:DC-DC CONVERTER WITH BIPOLAR OUTPUT AND ITS USE FOR CONNECTION OF A DISTRIBUTED GENERATION SYSTEM TO A BIPOLAR DC GRIDThe converter has an input for connecting a monopolar DC source and a bipolar DC output, with the same voltage but with opposite polarities. It is useful for the connection of a distributed generation system to a bipolar DC grid. For these applications, the proposed topology is a solution with sufficient guarantees of reliability, quality and performance. The converter circuit is very simple, it includes three inductors, four capacitors, two diodes and a power switch as a switching device.
Technology Transfer Office
Cracow University of Technology posted this:Low energy building design and thermal refurbishment of existing buildingsOUR MAIN GOALS Tools and good practice procedures for low energy building design, enabling to reduce demand on heating and prevent cooling demand while maintaining high indoor air quality. Because of the big volume of poor quality prefabricated apartment buildings, that still exist in Poland, one of our goals is also to elaborate a scenario of holistic revitalisation of those buildings in accordance with the requirements of sustainable development.